Universal Laser Systems X-600 User's Guide download pdf (Page 10)

DANGEROUS VOLTAGES ARE PRESENT WITHIN THE ELECTRONICSENCLOSURES

OF THIS SYSTEM. Access to these areas is not necessary during normal operation.

bec

omes

necessary to open one of these enclosures for service

easons

please

remember

to disconnect

the

power cord from your electrical

supply

NEVER REMOVE THE GROUND LEAD TO THE ELECTRICAL CORD AND PLUG THE

SYSTEM INTO A NON-GROUNDED OUTLET. A laser system that is not properly

grounded

hazar

dous

and has the potential to cause severe or fatal electrical

shock

Without proper

ounding

the

laser

system may exhibit sporadic or

unpredictable

beha

vior

Always plug the system into a

operly

grounded

(earthed)

outlet.

THE POWER SUPPLY CORD IS THE MAINS DISCONNECT DEVICE; THE EQUIPMENT

SHOULD BE LOCATED CLOSE TO AN EASILY ACCESSIBLE POWER OUTLET.

disconnect

the

equipment

from the supply

mains

the power cord should be

unplugged

from the power outlet

main power inlet (appliance coupler) of the

unit.

THE LASER SYSTEM IS DESIGNED AS A CLASS I, GROUP A, PLUGGABLE DEVICE.

also

designed for connection to

power systems which provide the most

flexibility

the

user

THIS DEVICE IS SPECIFICALLY DESIGNED TO COMPLY WITH CDRH PERFORMANCE REQUIREMENTS

UNDER 21 CFR 1040.10 AND 1040.11 AND TO COMPLY WITH EUROPEAN LASER SAFETY

REGULATIONS UNDER EN60825-1. CDRH is the Center for the Devices of

adiolog

ical

Health division of the

Food and Drug Administration

(FDA)

in the USA. No guarantees of suitability or safety are provided for any use

other than those specified by Universal Laser

ems

Laser Safety

This device contains a sealed carbon dioxide (CO2) laser that produces intense invisible laser radiation at a

wavelength of 10.6 microns in the infrared spectrum. For your protection, the laser is contained within a Class 1*

enclosure designed to completely contain the CO2 laser beam. CAUTION: Use of controls or adjustments or

performance of procedures other than those specified herein may result in exposure to hazardous levels of

invisible laser radiation.

•

intense light that appears during the engraving or cutting process is the product of material

ombustion

or vaporization. DO NOT STARE AT THIS INTENSE LIGHT FOR LONG PERIODS OF

TIME OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS SUCH AS BINOCULARS OR

MICROSCOPES.

•

This

device contains a visible Red Diode Pointer

(Class 3R)

to aid in positioning material to be cut or

eng

DO NOT LOOK DIRECTLY INTO THE RED LASER BEAM OR USE A REFLECTIVE

SURFACE TO REDIRECT OR VIEW THE RED LASER BEAM. NEVER ATTEMPT TO VIEW THE RED

LASER BEAM USING OPTICAL INSTRUMENTS SUCH AS BINOCULARS OR MICROSCOPES.

•

user door(s) are safety interlocked which will prevent the CO

laser beam from firing when the

user

door(s)

are

opened

Red Diode Pointer is NOT safety interlocked and can be automatically

activated with the

door(s)

either open or

closed

•

DO NOT OPERATE THE LASER SYSTEM IF ANY SAFETY FEATURES HAVE BEEN

MODIFIED, DISABLED OR REMOVED.

This

may lead to accidental exposure to invisible CO

laser

radiation which may cause severe

damage

and/or severe burns to your skin.

•

Always

use caution when

operating

a laser

em.

*An

enclosure which does not permit human access to laser radiation in excess of the accessible emission limits of

Class

for

the applicable

wavelength

and emission

duration.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 68 69

Comments to this Manuals

No comments

Universal Laser Systems X-600 User's Guide Page 10

Comments to this Manuals

Related products and manuals for Engraver Universal Laser Systems X-600