Universal Laser Systems X2-600 User Manual download pdf (Page 6)

The Advanced Output Center

Sullivan Center, Rm. 1232

312 629 6688 / [email protected]

This document is available electronically at http://crit.artic.edu/aoc

Page:6of12  LastModied:June10,201312:00PM

Focus Settings and Printing

Afteryouhavepreparedyourle,themachineandyourmaterialmustbepreparedforcutting.Sincethelaseractually

burnsthroughthematerialitcutsandengraves,itisveryimportanttoonlyuseapprovedmaterialsandtowatchthecutter

atalltimesduringtheoperationincaseofre.Cuttingthewrongmaterialsorusingthecutterirresponsiblycanresultin

harmtoyou,thelasercutterandthelabstaff,aswellasgeneratenestoyourstudentaccount.

Turnonthewallswitchnextto

theventalationpipe.

Hit“Escape”toexitfocus-

ingmode.Placethegauge

backintoitsslot,making

sureitdoesn’tstickout.

Alwaysturnthemachine

one,openthelid,andhit“Z”

BEFOREplacingyourmaterial.

Placethebaseofthefocusing

toolatonyourmaterial,and

lineitupslightlyinthefrontof

thelaserhead.

Focusissetwhenthelipofthe

focusingtoolisalignedwith

thebottomedgeofthelaser

carriage.Theatpartshould

beushwiththefaceofthelens

carriage,withthefocusingtool

sittingat.

Bydefaultthebedwillraiseandlowerbytenthsofan

inch.Usecautionwhenmovingthebedasitcancrash

intothelasercarriage.Whenthefocusingtoolgets

closetothelasercarriage,hitthe“check”button,then

raiseorlowerthelaserinhundredthincrementsusing

theupanddownarrows.

Remembertosetthefocusanytimeyou

startusingthemachine,aswellaswhen

youswitchtoamaterialwithadifferent

depth.

NOTE:Beforeusingthemachine,havealabmonitorchecktomakesurethecuttingtableisalignedproperly.

Printing the le

• Makesurethelasercutteristurnedon

• Beforeprintingyoushouldhavealabmonitorcheckyourfocusanddriversettings

• Onceyoursettingsarechecked,click“Print”tosendtheletothelasercutter

• Thelenamewillappearonthedisplaypanelofthelasercutter,alongwithpowersettingsfortherstcut.Ifthese

settingsallreadzeroand/orthemachinebeepsuponreceivingthele,thereisanerrorthatmustbecorrected.

Usuallythismeanswrongcolorsorstrokeweights.

• Withtheenclosurelidraised,pushingstartwilltraceoutthepathwithoutcutting.Makesurethecutsareinthe

properarea;adjusttheleifneeded.

• Nowhit“Pause”andclosetheenclosure.

• Withthelidclosed,hitting“Start”willcausethelasertoactuallycutthele.

• Youmustwatchthecutteroutputyourentirele.DONOTLEAVETHECUTTERRUNNINGUNATTENDED!

• Ifyouneedtotemporarilystopcutting,hitthe“Pause”buttonandWAITFORTHELASERTOSTOPCUTTING.The

cuttermustnishthelastlineitstartedbeforepausing;ifitisalonglineoraslowcut,itcantakeseveralminutesfor

thecuttertostop.

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Universal Laser Systems X2-600 User Manual Page 6

Comments to this Manuals

Related products and manuals for Engraver Universal Laser Systems X2-600